dois-je changer mon hdd

nantais02
Messages : 35
Inscription : jeu. 22 févr. 2018 20:33

dois-je changer mon hdd

Message par nantais02 »

bonjour,

j'ai acheté un hdd il y a quelques jours que j'ai mis dans mon nas.

J'ai quelques alertes sur ce hdd.

Voici son état smart : https://d.pr/i/jT6Av2

pouvez vous me le traduire car je ne suis pas sûr de comprendre

merci
nantais02
Messages : 35
Inscription : jeu. 22 févr. 2018 20:33

Re: dois-je changer mon hdd

Message par nantais02 »

et voici les messages d'erreur https://d.pr/i/qgn0c0

LU WWN Device Id: 5 000c50 0b0684406
Firmware Version: SC60
User Capacity: 10,000,831,348,736 bytes [10.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Oct 29 09:08:07 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 567) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 900) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 083 053 044 - 210251784
3 Spin_Up_Time PO---- 097 097 000 - 0
4 Start_Stop_Count -O--CK 100 100 020 - 4
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 96
7 Seek_Error_Rate POSR-- 072 060 045 - 14525430
9 Power_On_Hours -O--CK 100 100 000 - 43
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 100 100 020 - 2
187 Reported_Uncorrect -O--CK 085 085 000 - 15
188 Command_Timeout -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 065 065 040 - 35 (Min/Max 23/35)
192 Power-Off_Retract_Count -O--CK 100 100 000 - 2
193 Load_Cycle_Count -O--CK 100 100 000 - 4
194 Temperature_Celsius -O---K 035 040 000 - 35 (0 23 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 010 010 000 - 210251784
197 Current_Pending_Sector -O--C- 100 100 000 - 24
198 Offline_Uncorrectable ----C- 100 100 000 - 24
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
200 Multi_Zone_Error_Rate PO---K 100 100 001 - 0
240 Head_Flying_Hours ------ 100 253 000 - 42 (234 178 0)
241 Total_LBAs_Written ------ 100 253 000 - 29430081736
242 Total_LBAs_Read ------ 100 253 000 - 8636748071
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning

General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 5 Ext. Comprehensive SMART error log
0x04 GPL R/O 256 Device Statistics log
0x04 SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 2048 Pending Defects log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x13 GPL R/O 1 SATA NCQ Send and Receive log
0x15 GPL R/W 1 Rebuild Assist log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x24 GPL R/O 768 Current Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 24 Device vendor specific log
0xa2 GPL VS 16320 Device vendor specific log
0xa4 GPL,SL VS 160 Device vendor specific log
0xa6 GPL VS 192 Device vendor specific log
0xa8-0xa9 GPL,SL VS 136 Device vendor specific log
0xab GPL VS 1 Device vendor specific log
0xad GPL VS 16 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xc1 GPL,SL VS 8 Device vendor specific log
0xc3 GPL,SL VS 32 Device vendor specific log
0xc9 GPL,SL VS 8 Device vendor specific log
0xca GPL,SL VS 16 Device vendor specific log
0xd1 GPL VS 336 Device vendor specific log
0xd2 GPL VS 10000 Device vendor specific log
0xd4 GPL VS 2048 Device vendor specific log
0xda GPL,SL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 15
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 15 [14] occurred at disk power-on lifetime: 38 hours (1 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 53 00 00 00 00 1b 59 2f f8 00 00 Error: UNC at LBA = 0x1b592ff8 = 458829816

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 05 40 00 00 1b 59 2b 90 e0 00 1d+14:00:37.312 READ DMA EXT
35 00 00 05 40 00 00 1b 59 21 10 e0 00 1d+14:00:37.311 WRITE DMA EXT
35 00 00 00 80 00 00 1b 42 1b d0 e0 00 1d+14:00:37.311 WRITE DMA EXT
35 00 00 05 40 00 00 1b 42 16 90 e0 00 1d+14:00:37.309 WRITE DMA EXT
25 00 00 05 40 00 00 1b 59 26 50 e0 00 1d+14:00:37.308 READ DMA EXT

Error 14 [13] occurred at disk power-on lifetime: 38 hours (1 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 53 00 00 00 00 1b 59 1f 98 00 00 Error: UNC at LBA = 0x1b591f98 = 458825624

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 05 40 00 00 1b 59 1b d0 e0 00 1d+14:00:34.304 READ DMA EXT
25 00 00 00 80 00 00 1b 42 1b d0 e0 00 1d+14:00:34.304 READ DMA EXT
25 00 00 05 40 00 00 1b 42 16 90 e0 00 1d+14:00:34.279 READ DMA EXT
35 00 00 05 40 00 00 1b 41 fc 50 e0 00 1d+14:00:34.277 WRITE DMA EXT
35 00 00 02 b8 00 00 1b 22 38 88 e0 00 1d+14:00:34.276 WRITE DMA EXT

Error 13 [12] occurred at disk power-on lifetime: 38 hours (1 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 53 00 00 00 00 1b 59 0f 40 00 00 Error: UNC at LBA = 0x1b590f40 = 458821440

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 05 40 00 00 1b 59 0b 90 e0 00 1d+14:00:30.396 READ DMA EXT
25 00 00 05 40 00 00 1b 59 06 50 e0 00 1d+14:00:30.393 READ DMA EXT
25 00 00 05 40 00 00 1b 59 01 10 e0 00 1d+14:00:30.373 READ DMA EXT
35 00 00 05 40 00 00 1b 41 f1 50 e0 00 1d+14:00:30.372 WRITE DMA EXT
35 00 00 05 40 00 00 1b 41 ec 10 e0 00 1d+14:00:30.370 WRITE DMA EXT

Error 12 [11] occurred at disk power-on lifetime: 38 hours (1 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 53 00 00 00 00 1b 58 fe e0 00 00 Error: UNC at LBA = 0x1b58fee0 = 458817248

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 05 40 00 00 1b 58 fb d0 e0 00 1d+14:00:27.639 READ DMA EXT
25 00 00 00 80 00 00 1b 41 fb d0 e0 00 1d+14:00:27.633 READ DMA EXT
35 00 00 05 40 00 00 1b 41 e6 d0 e0 00 1d+14:00:27.630 WRITE DMA EXT
25 00 00 05 40 00 00 1b 41 f6 90 e0 00 1d+14:00:27.609 READ DMA EXT
35 00 00 05 40 00 00 1b 41 e1 90 e0 00 1d+14:00:27.608 WRITE DMA EXT

Error 11 [10] occurred at disk power-on lifetime: 38 hours (1 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 53 00 00 00 00 1b 58 de 30 00 00 Error: UNC at LBA = 0x1b58de30 = 458808880

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 05 40 00 00 1b 58 de 10 e0 00 1d+14:00:22.133 READ DMA EXT
25 00 00 05 40 00 00 1b 58 d8 d0 e0 00 1d+14:00:22.132 READ DMA EXT
25 00 00 05 40 00 00 1b 58 d3 90 e0 00 1d+14:00:22.130 READ DMA EXT
35 00 00 05 40 00 00 1b 58 be 90 e0 00 1d+14:00:22.129 WRITE DMA EXT
ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+14:00:21.613 FLUSH CACHE EXT

Error 10 [9] occurred at disk power-on lifetime: 38 hours (1 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 53 00 00 00 00 1b 58 cd d0 00 00 Error: UNC at LBA = 0x1b58cdd0 = 458804688

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 05 40 00 00 1b 58 c9 10 e0 00 1d+14:00:18.907 READ DMA EXT
25 00 00 05 40 00 00 1b 58 c3 d0 e0 00 1d+14:00:18.477 READ DMA EXT
35 00 00 00 20 00 03 02 7e b3 10 e0 00 1d+14:00:18.477 WRITE DMA EXT
35 00 00 05 40 00 00 1b 58 b4 10 e0 00 1d+14:00:18.475 WRITE DMA EXT
35 00 00 05 40 00 00 1b 58 ae d0 e0 00 1d+14:00:18.473 WRITE DMA EXT

Error 9 [8] occurred at disk power-on lifetime: 38 hours (1 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 53 00 00 00 00 1b 58 bd 78 00 00 Error: UNC at LBA = 0x1b58bd78 = 458800504

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 05 40 00 00 1b 58 b9 50 e0 00 1d+14:00:15.809 READ DMA EXT
ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+14:00:15.307 FLUSH CACHE EXT
35 00 00 05 40 00 00 1b 58 99 d0 e0 00 1d+14:00:15.305 WRITE DMA EXT
35 00 00 00 08 00 02 00 00 4a 28 e0 00 1d+14:00:15.304 WRITE DMA EXT
35 00 00 00 08 00 02 00 00 4a 30 e0 00 1d+14:00:15.304 WRITE DMA EXT

Error 8 [7] occurred at disk power-on lifetime: 38 hours (1 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 53 00 00 00 00 1b 58 ad 18 00 00 Error: UNC at LBA = 0x1b58ad18 = 458796312

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 05 40 00 00 1b 58 a9 90 e0 00 1d+14:00:12.134 READ DMA EXT
25 00 00 05 40 00 00 1b 58 a4 50 e0 00 1d+14:00:12.133 READ DMA EXT
35 00 00 05 40 00 00 1b 58 8a 10 e0 00 1d+14:00:12.132 WRITE DMA EXT
25 00 00 05 40 00 00 1b 58 9f 10 e0 00 1d+14:00:12.124 READ DMA EXT
ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+14:00:12.118 FLUSH CACHE EXT

SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 42 458770912
# 2 Short offline Completed without error 00% 42 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 35 Celsius
Power Cycle Min/Max Temperature: 22/35 Celsius
Lifetime Min/Max Temperature: 18/35 Celsius
Under/Over Temperature Limit Count: 0/43

SCT Temperature History Version: 2
Temperature Sampling Period: 3 minutes
Temperature Logging Interval: 59 minutes
Min/Max recommended Temperature: 10/25 Celsius
Min/Max Temperature Limit: 0/70 Celsius
Temperature History Size (Index): 128 (47)

Index Estimated Time Temperature Celsius
48 2018-10-24 04:53 ? -
... ..( 78 skipped). .. -
127 2018-10-27 10:34 ? -
0 2018-10-27 11:33 27 ********
1 2018-10-27 12:32 ? -
2 2018-10-27 13:31 18 -
3 2018-10-27 14:30 ? -
4 2018-10-27 15:29 22 ***
5 2018-10-27 16:28 31 ************
6 2018-10-27 17:27 31 ************
7 2018-10-27 18:26 31 ************
8 2018-10-27 19:25 32 *************
9 2018-10-27 20:24 32 *************
10 2018-10-27 21:23 33 **************
11 2018-10-27 22:22 33 **************
12 2018-10-27 23:21 34 ***************
... ..( 4 skipped). .. ***************
17 2018-10-28 03:16 34 ***************
18 2018-10-28 04:15 33 **************
19 2018-10-28 05:14 33 **************
20 2018-10-28 06:13 33 **************
21 2018-10-28 07:12 34 ***************
... ..( 4 skipped). .. ***************
26 2018-10-28 12:07 34 ***************
27 2018-10-28 13:06 35 ****************
28 2018-10-28 14:05 35 ****************
29 2018-10-28 15:04 34 ***************
... ..( 10 skipped). .. ***************
40 2018-10-29 01:53 34 ***************
41 2018-10-29 02:52 35 ****************
42 2018-10-29 03:51 34 ***************
43 2018-10-29 04:50 35 ****************
... ..( 3 skipped). .. ****************
47 2018-10-29 08:46 35 ****************

SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) supported [please try: '-l defects']

SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 6 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
gizmo78
Messages : 20037
Inscription : ven. 12 janv. 2018 17:44

Re: dois-je changer mon hdd

Message par gizmo78 »

juste pour les reallocated sectors tu peux le changer ;)
nantais02
Messages : 35
Inscription : jeu. 22 févr. 2018 20:33

Re: dois-je changer mon hdd

Message par nantais02 »

super merci
il était tout neuf pourtant , mais amazon expédie ça n'importe comment :roll:
Avatar de l’utilisateur
c0bw3b
Messages : 5507
Inscription : ven. 12 janv. 2018 17:44
Localisation : Lyon

Re: dois-je changer mon hdd

Message par c0bw3b »

Amazon ou un vendeur du MarketPlace revende aussi des pas vraiment tout neufs... :whistle:
(refurbished ou retour client d'un précédent achat)
gizmo78
Messages : 20037
Inscription : ven. 12 janv. 2018 17:44

Re: dois-je changer mon hdd

Message par gizmo78 »

bas la 46H il était neuf, après le transport....
TheMartel
Messages : 7550
Inscription : ven. 12 janv. 2018 17:44

Re: dois-je changer mon hdd

Message par TheMartel »

Ça se "reset" avec le bon matos ce genre d'information ;)
Répondre